Lubrication-free bearings keeping solar panel cleaning efficient

Treotham presents a new range of lubrication-free
plastic plain bearings ideal for use in semi-automatic cleaning machines designed
for solar surfaces.

Cleaning at lofty heights – this is the goal of TG
hyLIFT GmbH from Gronau. With their semi-automatic and easy-to-use cleaning
machines, they are already conquering the glass roofs and facades of the world
from Spandau station in Berlin to a modern shopping centre in Spain. The
company has developed the ‘hyCLEANER black SOLAR’ specifically for thorough
cleaning of solar plants. Engineers rely on the light, lubrication-free and
maintenance-free polymer plain bearings from igus in both the wheels and the
brush mount.

Solar and photovoltaic systems ensure production of
clean energy worldwide. The solar plant surfaces must be clean so that they can
work with optimum efficiency. Mainly used in agricultural areas, they are
subject to continuous dirt accumulation due to various environmental factors,
which reduce the economic efficiency of the surfaces. The performance of solar
plants of private operators is also affected in cities by fine dust and pollen,
which cannot be washed off by a rain. Even local dirt accumulation of
individual cells by bird droppings or lichens can reduce the efficiency of the
entire system due to the series connection, since the weakest module determines
the overall performance. This means a loss of 20 to 30 percent in numbers in
the worst case. But the financial loss is not the only problem: dirt can even
damage the coating and seals, which can lead to a total failure.

plant cleaning as a challenge for operators

Regular cleaning of solar and photovoltaic surfaces is,
therefore, an absolute must. This usually poses a major challenge for plant
operators and service providers, as the areas are difficult to access and
sensitive, and moreover the cleaning must be extremely thorough.

“The manual work by personnel is a common
solution here, which is dangerous and physically demanding,” explains
Andreas Grochowiak, Managing Director of TG hyLIFT GmbH.

The results are also based on individual performance;
besides, the effort required is also very high for several hundred square
metres of solar plant surface. The new semi-automatic cleaner hyCLEANER black
SOLAR from TG hyLIFT promises a simple and safe solution that assures up to
five times faster cleaning compared with manual processes. Due to the high
mechanical performance, an optimal cleaning result with low water consumption
is possible. The machine is easy to operate by radio remote control and allows
the operator to achieve an optimal cleaning result without physical effort.
With the hyCLEANER range, he can effortlessly clean up to 100 metres from one
spot. It is no longer necessary to step on the sensitive roof and solar areas,
thanks to the radio remote control. The electric motors of the machine are
powered by lithium-ion batteries with 36 volts like an e-bike, which means that
the operator can do without a power connection. Depending on the application,
the batteries last up to three and a half hours, and the charging time is only
two hours.

polymer bearings for reliable support

The hyCLEANER moves forward by means of four wheels on
two toothed belts. The belts are covered with special straps and exert their
grip on the wet surface. For example, the hyCLEANER can move on solar panels at
an angle of up to 35 degrees and can easily cross over maintenance aisles and
spaces between the panels of up to 30 centimetres. The wheels, which drive the
hyCLEANER via a plastic toothed belt, are made of POM material and guided via a
stainless steel shaft.

“In order to prevent wear between the two
materials and thus increase the service life of the cleaning machine, we
decided to use iglidur P plain bearings from igus,” explains Grochowiak. The material is specifically designed for outdoor use and only
absorbs moisture in very small quantities. It is resilient and has a low wear
rate. It is also free of lubrication and corrosion like all igus materials,
thanks to its polymer base.

flange bearing for use in wet environments

For starting up the cleaning machine, the user only
needs a water connection. A reeling device provides a simple and user-friendly
hose management system over several metres. The solar surfaces are cleaned with
water and a special 90-centimetre wide cleaning brush having a diameter of 30
centimetres. Upon request, other sizes can be implemented quickly and easily,
thanks to the modular system of the hyCLEANER black SOLAR. The brush rotates at
up to 400 revolutions per minute. This is supported by an igubal EFSM fixed
flange bearing, which is easily and quickly installed on the shaft end of the
brush compensating for misalignment. The spherical ball of the fixed flange
bearing is made of the high-performance plastic iglidur W300, which is
characterised by extremely high wear resistance and long service life.

Grochowiak is convinced of the quality of the
igus bearings: “It’s been several years since we have been relying on
igus’ lightweight plain bearing technology in our machines. For example, it is
successfully used in our hyCLEANER blue EVO series for the cleaning of glass
and other surfaces as well as in the hyCLEANER red EVO series for the cleaning
of facades.”

used around the world

TG hyLIFT GmbH sells its cleaning systems all over the
world and sees the best opportunities for its products in the future.

“The concept of such a solar plant cleaning is
still largely unknown in the industry, so we have to start here and convince
both solar system operators and service providers in the Facility Management
industry of our product,” explains Grochowiak.

The advantages are obvious: The user saves time and
resources, and increases the safety of his employees. The semi-automatic
cleaning machine is used, for example, at the Stade de Suisse in Bern, where
the hyCLEANER regularly cleans 12,000 square metres of solar space. The solar
plant cleaning system is also used in modern architecture, such as the Arnhem
Centraal train station in the Netherlands and at the Marineda City shopping
centre in Spain. Further projects are currently underway in Estonia and Spain.
Always present: the polymer bearings from igus.

bearings from Treotham Automation

The iglidur bearings from igus, as well as all igus
products are available at Treotham across Australia. Give our staff a call to
find out which long life bearing will be suitable for your application.

For more information, please visit the Treotham
Automation website
or call 1300 65 75 64.

Leave a Reply

© All Rights Reserved. All content published on this site is the property of Prime Creative Media. Unauthorised reproduction is prohibited