Controlling an Unmanned Car

In 2001, Congress set a goal that by the year 2015 one-third of all military combat ground vehicles would be able to drive themselves. The first Grand Challenge was run on March 13, 2004, when none of the 15 vehicles that entered completed more than 5 percent of the course. The failures of the first race and a doubling of the amount of the prize has brought a number of new players to the race this year. One team, formed by Jim Crittenden and several colleagues, may have a special edge. The members of Team Mojavaton are experienced in various aspects of custom machine building, design, vision systems, control systems, electronics, programming, and project management. Crittenden is also the Automation and Manufacturing Manager at CoorsTek.

All the teams this year could benefit from the lessons of the previous race. They just had to glean those lessons from the technical reports prepared by last year's final 25 teams and from the instrumentation data they submitted. "One of the things we noticed by reading the technical reports and by watching the videos is that many of the teams had auxiliary generators," Crittenden says. "A couple of teams actually had gasoline-powered generators hanging off the backs of their vehicles."

One of the first things that the team did was to make a list of the loads and their power requirements for the sensors, the programmable logic controllers, and the computer—everything that it would add to the vehicle. Through careful attention to power use in its design, the vehicle consumes only 25A at 14V for all its navigation and automation systems. This is well within the capability of the 90A alternator on the vehicle and still allows the air-conditioner to cool the passenger compartment.

"The system really comes down to only two things that you need to know," Crittenden says. "Going down the road, I need to know where to turn the steering wheel and I need to know what to do with the throttle and the brake." With this information in hand, it becomes a matter of how quickly and precisely the system can react to it.

The autonomous brake uses a pneumatic cylinder that applies pressure rather than the controlled displacement through servos of the steering wheel and throttle. For the servo motors, the team selected units with the highest RPMs at the lowest voltage level to consume the least amount of power.

For controlling the steering and throttle, the team selected Galil's DMC-1416 single-axis controller and drive combination. Lisa Wade, vice president of sales and marketing at Galil Motion Control, notes, "One of the things that they use in our controllers is the Position-Tracking Mode." This allows the system to send new points on the fly. It does not have to get to the previously commanded position if new sensing data indicates an alternate position. The controller responds in real time. This is important because the vehicle has to make about 10 decisions per second to determine the correct direction and velocity.

Galil initially added the Position-Tracking Mode to controllers for a similar application where instant adjustments were required. Since that first application, the need for this capability occurred enough that it became a standard feature on two products. Without the Position-Tracking Mode, the typical motion control system has to reach the target destination before it accepts new commands.

In many respects, the autonomous vehicle is similar to an advanced system, except it must face a number of undetermined obstacles. According to John Wade, a senior application engineer at Galil, the motor control portion of the vehicle is rather straightforward: "They have an encoder on the motor, so we take in the encoder signal, and close the loop around it. We are able to take in the position from their device that is providing the position information and drive the motor to that location as fast as possible."

Motion control is obviously just a portion of the overall control system. Each car in the race has a GPS receiver. Two hours before the start of the race each team receives a CD with a text file of the coordinates that must be loaded into the vehicle's computer. Crittenden expects it will take about 5 min to load their system.

On the course, the vehicle drives from one waypoint to another. Along the route, however, there are ditches and at least one DARPA-planted tank trap. The vehicle has to "see" the road ahead and avoid these show-stopping hazards. "We have a variety of sensors in our car, all of which see the world in a slightly different manner," Crittenden says.

With the technical work behind them, the activities on the race day should be straightforward once the team gets its GPS file. Crittenden says, "You load it in, drive your car up to the starting line, switch it into autonomous mode, get out, close the door, and watch it drive off. You hope to see it 10 hrs later, 150 miles away."

A decision was made on June 6 that Team Mojavaton is among the 40 teams chosen to move onto the next level of the 2006 challenge.

Custom Design FlexibilityRandy FrankRecognized worldwide as a leader in motor manufacturing, HSI's stepper motors, linear actuators, hybrid stepper motors, low-voltage drives, and sealed switches are used in much of today's sophisticated medical equipment, instrumentation, machinery automation, printing, HVAC equipment, robotics, aerospace, and precision motion applications. The company's manufacturing facility, located on 10 acres in the heart of Connecticut, boasts some of today's most efficient technology and manufacturing methods. HSI currently ships an extensive line of motors and switches throughout the world to OEM's in the Americas, Europe, Asia, and Australia.Available in five basic frame sizes: 15 mm, 20 mm, 26 mm, 36 mm, and 46 mm, HSI's linear stepper motors are available in captive, non-captive, or external linear versions, and can deliver up to 22.67 kg of thrust. Step increments range from 0.04064 cm to 0.0003175 cm per step depending on the step angle of the motor and pitch of the lead screw. HSI's rotary motors are built to provide exceptionally high torque-to-size ratios. Standard prototypes typically have a rapid 48-hr turnaround.HSI's line of hybrid linear actuators opens new avenues for equipment designers who require high performance and exceptional endurance in a very small package. The various patent-pending designs use a proprietary manufacturing process, which incorporates engineering thermoplastics in the rotor drive nut and a stainless steel acme lead screw. This allows the motor to be much quieter, more efficient, and more durable than the v-thread and bronze nut configuration commonly used in other actuators. Motor life is improved more than 10 times over the traditional bronze nut style—and it requires no maintenance and does not affect the cost. An additional feature is the bearing preload adjustment, which unlike other designs, does not protrude from the motor configuration commonly used in other actuators. The HSI hybrid actuators come in six sizes: 21 mm, 28 mm, 35 mm, 43 mm, 57 mm, and 87 mm. Each size has three designs available—captive, non-captive, and an external linear version. The 43 and 57 mm are available in a linear rotary version, which provides independent linear and rotary motion. There are 25 different travels per step available from 0.0001524 cm to 0.0127 cm. Microstepping can be used for even finer resolution. The 87 mm actuator delivers up to 226.79 kg of force. These linear actuators are fit for applications requiring a combination of precise positioning, rapid motion and long life.The company's hermetically sealed switches are fit for use in the harsh environments typically found in aerospace applications. High temperature versions can operate at up to 427C. HSI's switches are in service on most commercial aircraft as well as on military aircraft and the space shuttle. HSI switches are built to meet stringent military specifications. To achieve and sustain such high levels of quality requires a combination of skilled engineering and production teams, special support facilities, and coordinated quality control from design through production. HSI's capabilities encompass all of these factors, and therefore HSI's switches are considered a hallmark throughout the world. In addition to aerospace applications, these switches are well suited for industrial applications, including oil industry field equipment, gas turbines, and high-temperature instrumentation.Whether an application requires a standard item, custom, design, new product, or more sophisticated complete assembly, in high volume or limited run, HSI's experienced engineering team will assist you.Haydon Switch & Instrument Inc. http://rbi.ims.ca/4412-151

Web Resources

For more information on Team Mojavaton http://rbi.ims.ca/4412-531 For more information on Galil Motion Control DMC-1416 http://rbi.ims.ca/4412-532