Kennards Concrete Care
2/16 Herbert St
Artarmon NSW 2064
Tel: 02 9906 7188
Fax: 02 9906 7550

Supplier´s Website
Enquire now

Incorrect details?

close

Enquire NowVisit Website

Contact Details

Kennards Concrete Care introduces deep cutting concrete saw

Deep cutting concrete saw

A new, hydraulic powered hand saw, which cuts through concrete or rock to a depth of 200mm, has been introduced by Kennards Concrete Care .

Cutting to such a depth normally requires pre-cutting with a demolition saw before a ring saw is introduced.

However, the new saw is an all in one unit, used first to make a pre-cut and then a full incision.

The deep cutting concrete saw offers other advantages as well, including flush cutting, easy handling and greater reliability.

The saw can be used fume-free indoors with a remote petrol or three-phase hydraulic power pack from Kennards Concrete Care, which has outlets in Sydney, Melbourne and Perth.

A major feature of the saw is that the two-piece guard pulls apart easily to enable flush cutting. The deep cutting concrete saw’s 535mm diameter overside blade cuts to 200mm, even when the diamond blade is almost worn out.

While the size of the blade might easily give the impression that the saw is difficult to handle, it is in fact safe and ergonomic. Being well balanced, the operator does not experience inertia and swaying when starting up and slowing down.

The deep cutting concrete saw has a ramped start-up, taking about 15 seconds to attain full speed and allowing the operator total control.

The saw also offers advantages in reliability:

• Unlike a ring saw, it has minimal moving parts, meaning less chance of mechanical failure
• A built-in pressure relief valve enables the correct oil flow to the head, saving down-time while the seal is changed
• The new Micro V belt is also quick and easy to adjust
• A trigger on the hand control turns the water on and off instantly
• The saw is powered by a 9.5ccm motor and without blades and hoses weighs 12kg

Kennards Concrete Care News

Floor preparation machines for reconstruction projects from Kennards Concrete Care (5-Sep-2008)
Three different floor preparation machines, available from Kennards Concrete Care, saved days of work for a contractor during a reconstruction project in a major Perth shopping complex.

Husqvarna 680 grinder from Kennards Concrete Care (20-Aug-2008)
A new, Husqvarna 680 grinder from Kennards Concrete Care proved suitable for a challenging job during the construction of an office block at Perth Airport. The large planetary grinder is among a range of new Husqvarna equipment which has been purchased by Kennards Concrete Care for its hire centres in Perth, Adelaide, Melbourne, Sydney and Brisbane.

Kennards Concrete Care’s Darda C12 Hydraulic Splitter for Ridgeway Gold Mine (14-Aug-2008)
In early June 2008, Kennards Concrete Care supplied a Darda C12 Hydraulic Splitter for a trial at the Ridgeway Gold Mine, located near Orange in the central west of NSW. The Darda C12 Hydraulic Splitter was used to break some oversize boulders which had been specially selected and trucked from the production level 850 metres below surface.

Diamond chainsaw available from Kennards Concrete Care (10-Jul-2008)
A new diamond chainsaw, hired from Kennards Concrete Care, enabled a demolition contractor to cut five door openings through double brick in additional quick time during a major refurbishment project. The chainsaw, which can also be used on reinforced concrete, masonry and rock, plunge cuts to a depth of 350mm.

View all  |  RSS Feed

Related Articles

Maxi storage system from Spacepac Industries designed with Louvred panels (13-Oct-2008)
Spacepac Industries refer Louvred Panels as the backbone of the Maxi storage system. These Louvred panels are pressed steel panels designed to allow all sizes of Maxi bins to hang in a high density, free configuration, suitable for small parts picking. The special lip on the rear of the bin is seated over the louvre of the panel.

Watlow FIREROD heater enters 50th year of cartridge heating (13-Oct-2008)
The Watlow FIREROD heater, available from Watlow, enters its 50th year of swaged cartridge heating. With premium materials and tight manufacturing controls, the FIREROD heater continues to provide quality heat transfer, uniform temperatures and resistance to oxidation and corrosion even at high temperatures.

Collapsible bulk bins from Spacepac Industries engineered for multiple applications (10-Oct-2008)
Spacepac Industries believe that economical storage of manufactured goods, perishable products or recycling materials are essential. The collapsible bulk bins from Spacepac Industries are easy to use and can be used for multiple applications.

Burny 10 LCD Plus system from Profile Cutting Systems (9-Oct-2008)
Profile Cutting Systems offer the Burny 10LCD Plus, which is the next step in PC-based motion control. Designed for multiple axis cutting machines, the Burny 10LCD Plus features advances in CNC technology on a proven platform, which is engineered to increase productivity and reduce costs.